I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu
User Login
User Name
Password



View By Aircraft
Users Aircraft

Browse Images

Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference
Page (7 in total) :  1   2   3   4  [ 5 ]  6   7  [ < Prev ] [ Next > ]
Hangar Aircraft Category Date Preview
LASTWOODSMANSIG Customaire # FF-26 Parked15-Jul-17 07:16
Views : 281
TOP VIEW - I made two extra wing photocopies, and highlighted the ribs to glue, with blue color, and covered them with waxed paper, and "lined them up" with the plans. This was to set the ribs on, without sticking, when they dried in the first part of "double gluing".
LASTWOODSMANSIG Customaire # FF-26 Parked15-Jul-17 07:14
Views : 242
SIG "Customaire" 22" free flight rubber - SIDEWAYS VIEW - The ribs are all in place (not glued yet), and are snug and flush, and braced up, and checked for easy removal for the first gluing of the "double gluing" procedure. The thin bracing planks for the tops of the ribs (to hold the rib bottoms flush to the building board), are cut out and ready to go.
LASTWOODSMANSIG Customaire # FF-26 Parked15-Jul-17 07:11
Views : 255
I had forgotten - but now have put in - the small inside bracing planks for the LE and TE parts. Now, the LE and TE parts are braced into their location on both sides. In woodworking, "you can never have too many clamps!" (a wise man once said). All of this fussing should make the gluing operation very smooth and easy, hopefully!
LASTWOODSMANSIG Customaire # FF-26 Parked14-Jul-17 09:17
Views : 240
The LE and TE are now held down flat to the board, with the tips of long thin planks, placed on top of the LE and TE, with these planks being pinned to the board.
LASTWOODSMANSIG Customaire # FF-26 Parked14-Jul-17 09:16
Views : 233
The 3/32" sq LE is now braced up in position, with long straight planks. The ribs are now also braced up with the other side location planks, that are pinned to the table on the other side of the ribs. The ribs were then slid forward up against the LE, and the rear 3/32" X 3/16" TE was then slid up snug to the rear of the ribs, and the TE is also braced up with a long plank pinned to the table, insuring a snug, flush slip fit to the back of the ribs. All of these laser cut ribs fit perfectly!
LASTWOODSMANSIG Customaire # FF-26 Parked14-Jul-17 09:14
Views : 260
MAIN WING ASSEMBLY - The parts, and the 3/32" square Leading Edge (LE) and the 3/32" X 3/16" Trailing Edge (TE), are now laid out, for the right and left wing sections. The bracing planks, for one side of the ribs, are now pinned to the building board to hold the ribs in position.
Hangar Aircraft Category Date Preview
LASTWOODSMANSIG Customaire # FF-26 Parked13-Jul-17 23:43
Views : 314
DASTARDLEY AND MUTLEY
LASTWOODSMANSIG Customaire # FF-26 Parked13-Jul-17 23:41
Views : 272
FARTING DOG PLANE
LASTWOODSMANSIG Customaire # FF-26 Parked13-Jul-17 19:11
Views : 224
The total weight of the lower sequi wings alone together = 0 grams. The total weight of all four assemblies together = 2 grams (my scale only measures to one gram graduations).
LASTWOODSMANSIG Customaire # FF-26 Parked13-Jul-17 19:09
Views : 236
Fin/rudder, stabilizer, and left and right lower sesqui wings frames are completed now and finished sanded.
LASTWOODSMANSIG Customaire # FF-26 Parked13-Jul-17 19:08
Views : 250
SIG "Customaire" bipe 20" The lower sesqui wings are sanded up to airfoil shape to 320 grit sandpaper. The 1/16" X 1/8" trailing edge and the 3/32" sq leading edges were very hard balsa - very hard to sand, but at least I got it done without breaking anything.
LASTWOODSMANSIG Customaire # FF-26 Parked10-Jul-17 12:29
Views : 284
Note the "folding prop".
Page (7 in total) :  1   2   3   4  [ 5 ]  6   7  [ < Prev ] [ Next > ]