I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Top Ten Aircraft : (numbers in brackets represent number of images online) Guillows Series 400 - P-51 Mustang (953) Guillows Series 200 - SE5a (941) Guillows Series 800 - Stearman PT-17 (698) Guillows Series 2000 - B-29 Super Fortress (679) Guillows Series 800 - Sopwith Camel (661) Guillows Series 500 - P-40 Warhawk (612) Molt Models Tyro (601) Guillows Series 400 - P-40 Warhawk (553) Guillows Series 1000 - F4U Corsair (522) Guillows Series 200 - Fokker DR-1 Triplane (505) ... View All Aircraft Top Six Manufacturers : Guillows Scratch Built Dumas Dave Diels Engineering, Inc Comet ManzanoLaser ... View All Manufacturers

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (45 in total) :  <<   26   27   28   29   30   31   32   33   34   35   36   >>  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview pfinn Shortys Basement BV-215 Build 18-Jul-09 21:20 Views : 744 Where the laser cut infill pieces met the "use scrap to infill" with a butt joint, I beveled the mating surfaces to create a stronger Lap joint. Worked out well. pfinn Shortys Basement BV-215 Reference 16-Jul-09 04:58 Views : 796 I do believe the pilot dropped something and is frantically searching the cockpit floor ( that's why you can't see him, or her! Painted this back in school in '85. pfinn Shortys Basement BV-215 Build 15-Jul-09 03:48 Views : 781 Started infill on nose. Extendedback on the bottom for landingson the hard stuff. pfinn Shortys Basement BV-215 Build 15-Jul-09 03:45 Views : 824 Bevel the infill pieces where needed. And remember to sand off the laser " Ala Chara" on the seams... unless you prefer little black lines on your joints...(ahem). pfinn Shortys Basement BV-215 Build 15-Jul-09 03:34 Views : 790 The wingroot sheet infill pieces are precut.Went in wonderfully. Glued in the two adjacent stringers on nose and tail only first, then lower adjacent stringer where indicated by laser marking on only F3 and F6 (nose is F1). Then glue lower infill piece to formers using the stringer two glue points like a shelf. finishinish gluing stringers, Add top wing root infill piece. Done. pfinn Shortys Basement BV-215 Build 14-Jul-09 02:34 Views : 817 Exhaust trough. The "Active Air Ducting" is used to help reduce drag (venturi like during boost as wel as eliminating turbulence around the motor nozzle. The trough gets lined as well woth paper then aluminum foil. Hangar Aircraft Category Date Preview pfinn Shortys Basement BV-215 Build 14-Jul-09 02:25 Views : 725 Intake, pfinn Shortys Basement BV-215 Build 14-Jul-09 02:21 Views : 754 Everything to make it go done. The paper is 67 lbs. Vellum Bristol ( used for "Fiddlers Green" models). pfinn Shortys Basement BV-215 Build 14-Jul-09 02:15 Views : 733 The air duct will continue thru to F4. pfinn Shortys Basement BV-215 Build 14-Jul-09 02:12 Views : 816 Installing the "Rapier" L2 or L2HP motor tube and the "Active Ducting". pfinn Shortys Basement BV-215 Build 12-Jul-09 03:49 Views : 773 Formers and outer keel strip in place. Ready to come off and add other side. Onlt the forward and aft formers have notches for the stringers. The remainder have small laser marked centerlines indicated on the formers. If you look closely you can see them. pfinn Shortys Basement BV-215 Build 12-Jul-09 03:42 Views : 743 Started fuselage. Keel parts down. Page (45 in total) :  <<   26   27   28   29   30   31   32   33   34   35   36   >>  [ < Prev ] [ Next > ]