| Hangar |
Aircraft |
Category |
Date |
Preview |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 05-Feb-16 14:45 |  | | Views : 522 | | another shot of the assembledge. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 05-Feb-16 14:44 |  | | Views : 529 | | Took some time to assemble the bones today and check the fit everything. |
| rayl | Scratch Built Loening OL-8 Amphibian | Reference | 02-Feb-16 13:05 |  | | Views : 467 | | BTW. Weather Report for NW Iowa: 10-14" wet snow & 30-50 MPH winds. At least teh Darn Caucuses are over and evrybody has moved on. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 01-Feb-16 14:53 |  | | Views : 505 | | THis is my "proof of concept" test piece. As I mentioned aearlier, I've never built a covered wing before so I am trying out various methods of covering it. I have tried the dope/thinner covering method, the glue stick method and several mixes of water and water/alcohol to shrink the tissue, just to get comfortable with how to proceed. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 01-Feb-16 14:49 |  | | Views : 480 | | All of the wing bones and "N" struts done. Now I have to cut away the ailerons before final sanding and sealing. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 01-Feb-16 14:44 |  | | Views : 470 | | To carry on the conversation that DD started: The engine structure here was wrapped with 1/16" SOFT balsa. I edge-glued sheets together with Cyno then sprayed it down with WIndex, wrapped it around a piece of PVC pipe about the right diameter and let it dry overnight, The sheeting was CYno'd to the structure and trimmed. The front fairing was tacked to the fuselage, sprayed with Windex, then held in place with painters tape until dry (X 2 to get the other side). IT may be just my imagination, but the Windex seems to have just enough Ammonia in it to really relax the wood grain. |
|
| Hangar |
Aircraft |
Category |
Date |
Preview |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 31-Jan-16 14:38 |  | | Views : 470 | | Detretuis from converting about 10 ft of 1/8" X 5/16" basswood to airfoil shaped strut material. Now I just have to figure out how to make the joints in the "N" struts. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 25-Jan-16 23:18 |  | | Views : 475 | | Another view of the saddles. Out of scrap balsa I built 4 different sanding blocks fair teh airfoil. If some ham-handed idiot wouldn't have crushed several ribs during the process, requiring replacments, I would hav been done much sooner. Now on to the strut & rigging attachment points. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 25-Jan-16 23:14 |  | | Views : 519 | | Spent most of the day sanding and strueing up the wings. Never done this before. My enigineering & woodworking background has proven the worth of "jigs" over the years. Here is one of teh wings supported by three saddles that allowed me to get the bottom of the leading & trailing edges truly flat and also make sure that the undercamber of the airfoil was consistent. |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 22-Jan-16 19:29 |  | | Views : 505 | | Anothee view. Span is 40 inches (+ asmidge). |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 22-Jan-16 19:25 |  | | Views : 465 | | Top wing done. The plans that I am working off of did not have ailerons, so had to extrapolate/interpolate/WAG them; think that I'm pretty close. The wing center section/dihederal brace took most of the day (when I wasn't shoveling snow). |
| rayl | Scratch Built Loening OL-8 Amphibian | Build | 20-Jan-16 11:55 |  | | Views : 509 | | Nearly 200 individual parts here, Took a day and a half to git R done. The little pile in front are the puchings from the alignment tool. I think the next model will be Laser-cut. |
|
