I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Cleveland de Havilland Mosquito View Details View All Switch Aircraft Users Aircraft David Duckett Modelboy

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (9 in total) :  1   2   3   4  [ 5 ]  6   7   8   9  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview David Duckett Cleveland de Havilland Mosquito Parked 10-Mar-14 16:47 Views : 583 http://en.wikipedia.org/wiki/Airfoil David Duckett Cleveland de Havilland Mosquito Build 10-Mar-14 05:30 Views : 567 The plan has no stringers on the top of the ribs but you know that's not going to happen. The 18" ruler shows the size. All the notches for these stringers will be done with the xacto. David Duckett Cleveland de Havilland Mosquito Build 10-Mar-14 05:26 Views : 516 I wrapped the plan around the building board to keep it intact. This is the only thing that will be built directly on the plan. Patterns for for the other structures were done with traving paper. As I've used nothing from the kit I'll be putting it back on ebay when I'm finished with it. David Duckett Cleveland de Havilland Mosquito Build 10-Mar-14 05:22 Views : 614 I used the parts in the kit as patterns for the pieces I'm actually using to build the kit. I left extra wood at each end of the rib so it can be cut to fit precisely. David Duckett Cleveland de Havilland Mosquito Build 10-Mar-14 05:16 Views : 611 It's very important to insure the leading and trailing edges are prevented from warping by the addition of the ribs so they are pinned in place on the outsideof, not through, the wood. Due to the curvature of the bottom of the ribs, the aileron spar must also be blocked up. David Duckett Cleveland de Havilland Mosquito Build 09-Mar-14 05:48 Views : 547 Hangar Aircraft Category Date Preview David Duckett Cleveland de Havilland Mosquito Build 09-Mar-14 05:47 Views : 543 The plans say to block up the leading and trailing edges but do not say how much. I pinned the front spar in place and then set the outer, inner, and middle ribs in place. THe leading and trailing edges were then set in place using the ribs as guides. The leading edge is 1/4" x 1/2", spars and trailing edge are 1/8" stock, and the aileron spar is 3/16" stock. David Duckett Cleveland de Havilland Mosquito Build 06-Mar-14 05:22 Views : 560 For now..... David Duckett Cleveland de Havilland Mosquito Build 06-Mar-14 05:18 Views : 504 The front of the nacelles will get another half inch of wood or so before final shaping. David Duckett Cleveland de Havilland Mosquito Build 06-Mar-14 05:14 Views : 511 I plan to have the wheel wells open to some degree and that will mean removing lots of wood once the landing gear doors are fabricated. No specific ideas are in place yet but I find it helps to think about the tasks ahead without formulating a particular plan. Sometimes the solution will suddenly seem clear as a day in Arizona. David Duckett Cleveland de Havilland Mosquito Build 06-Mar-14 05:08 Views : 473 The mosr difficult part of the build will be the installation of the landing gear so I'm stopping the infill here until I figure that out. David Duckett Cleveland de Havilland Mosquito Parked 06-Mar-14 05:05 Views : 500 Page (9 in total) :  1   2   3   4  [ 5 ]  6   7   8   9  [ < Prev ] [ Next > ]