I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu
User Login
User Name
Password



View By Aircraft
Users Aircraft

Browse Images

Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference
Page (8 in total) : [ 1 ]  2   3   4   5   6   7   8  [ Next > ]
Hangar Aircraft Category Date Preview
David DuckettDumas Kit #233. MiG 17Reference26-Jan-21 13:48
Views : 901
I had been home from getting a Covid-19 vaccination at the VA about 20 minutes when this happened. Snowed for 25 minutes!!
David DuckettDumas Kit #233. MiG 17Build21-Jan-21 06:33
Views : 893
A few panel lines to finish....
David DuckettDumas Kit #233. MiG 17Flying19-May-17 20:48
Views : 1021
The caption said it's a 15, not a 17.
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Jan-17 09:57
Views : 1043
This pic goes BACK into my Hangar ...
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 17:15
Views : 1214
This brief "Flight Story" about Van Coc on "Historic Wings", tell the REAL story of the Air War in Vietnam... website - http://fly.historicwings.com/2012/12/north-vietnams-leading-ace/
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 17:11
Views : 1066
The best US Ace had 6 kills.
Hangar Aircraft Category Date Preview
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 17:09
Views : 1075
"Nguyen Van Coc" - North Vietnam's leading Ace - 9 kills.
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 17:03
Views : 1159
AFTERTHOUGHT Looking Back ... I should have -1- glued the rudder on straight as per David Duckett's Mig 17 build (I had read it but forgot), -2- installed the rear view Periscope by the canopy, -3- installed wing fuel tanks, -4- built wing Anhedral (not the kit dihedral), as per D.D., -5- installed the third cannon beside the first two cannons, -6- made four K-5 air to air missiles, now that I researched it all....
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 16:53
Views : 1196
Then I turned the trim sheet over and cut out all of the strip patterns I had traced on the back, peeled off the backing, and stuck each strip onto its canopy frame location. I added a little extra width on the canopy bottom strips, so that they woould extend down onto the fuselage a little bit further, to hide the canopy/fuse intersection line, and I painted little touchups on the intersection line of the canopy bottom frame where it met the fuse tissue.
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 16:46
Views : 1129
CANOPY COCKPIT FRAME The clear 0.020" thick cockpit canopy frames were made as follows... I used white printer paper to cut thin strips for the frames by sizing and recutting and test fitting them over the canopy frame. When they all fit and matched the frame nicely, I traced them onto the back of a Top Flite Trim Sheet (peel 'n stick) - but did not cut them out yet. On the coloured front of the trimsheet, I used the same acrylic paint colors that I mixed up that matched the camo tissue colors, and painted over the whole front of the color side of the trim sheet in the same camo pattern and let it dry.
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 16:37
Views : 1099
LASTWOODSMANDumas Kit #233. MiG 17Parked27-Dec-16 15:34
Views : 1103
I used acrylic paints mixed up as best I could to match the camo tissue covering.
Page (8 in total) : [ 1 ]  2   3   4   5   6   7   8  [ Next > ]