| Build Thread, Page :
[ 1 ] 2 (36 posts, 20 posts per page, 2 pages in total)
|
[ Next > ] |
| rgood, Image # 34847 | 31 Oct 15 18:14 |
Need to work on that cowling.... |
| rgood, Image # 34846 | 31 Oct 15 18:13 |
Slow progress..... |
| rgood, Comment for image # 34819 | 30 Oct 15 11:51 |
| Thanks Don. Paper clips, balsa and brown (mixed) acrylic. Not quite at the finished look yet! |
| Don C, Comment for image # 34819 | 30 Oct 15 10:24 |
| Nice. I really like the "bentwood" chair. |
| rgood, Image # 34820 | 27 Oct 15 13:24 |
Slopw progress - deck work and general home stuff being done. |
| rgood, Image # 34819 | 27 Oct 15 13:22 |
..some cockpit work. |
| rgood, Image # 34818 | 27 Oct 15 13:21 |
Learning to cover in Solite! |
| rgood, Comment for image # 34764 | 18 Oct 15 13:53 |
| Thanks Don - I used some Drafting film (I am an ex-draughtsman) it is very fkexible and does not split easily.
We will see how it lasts as I have a lot of opening and closing, of that door, to finish the details! |
| Don C, Comment for image # 34764 | 18 Oct 15 13:44 |
| Impressive! How did you hinge the door? |
| rgood, Comment for image # 34764 | 18 Oct 15 11:49 |
| Started to attempt some cockpit work - had to cut out a couple of roof members in fuselarge and put some "beefing up" pieces around too. Mock-up panel print, it is 2" wide. Rudder pedals, trim, throttle & mixture quadrants to make too. |
| rgood, Comment for image # 34765 | 18 Oct 15 11:44 |
| Thank you Rayl! The plastiuc cowling looks better on this (port) side, the other side will need some filling & sanding! |
| rayl, Comment for image # 34765 | 18 Oct 15 11:19 |
| looking VERY nice! The vac-form parts look like they don't fit to bad. |
| rgood, Image # 34765 | 18 Oct 15 10:25 |
|
| rgood, Image # 34764 | 18 Oct 15 10:24 |
|
| Don C, Comment for image # 34753 | 17 Oct 15 10:13 |
| Nice job! |
| rgood, Comment for image # 34752 | 16 Oct 15 13:43 |
| Thanks David. The decals in the box look fine - so I hope they will do the job. |
| David Duckett, Comment for image # 34753 | 16 Oct 15 13:42 |
| Fill and sand, of course:-) |
| David Duckett, Comment for image # 34752 | 16 Oct 15 13:38 |
| There is no "how to" for water slide decals as they have always worked easily for me. They will not adhere to a less than smooth surface. The only decals that have needed the spray before treatment are those from Diels which are very fragile. |
| rgood, Comment for image # 34752 | 16 Oct 15 12:22 |
| Thinking far into this build David - where can I find your "How to" on the Guillows decals and your method of application. I recall that you pre-spray the sheet before going ahead with the transfer? (My decal sheet is over 12 years old!) |
| rgood, Comment for image # 34752 | 16 Oct 15 12:17 |
| By the By!!!!! |
| Build Thread, Page :
[ 1 ] 2 (36 posts, 20 posts per page, 2 pages in total)
|
[ Next > ] |
