I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Top Ten Aircraft : (numbers in brackets represent number of images online) Guillows Series 400 - P-51 Mustang (953) Guillows Series 200 - SE5a (941) Guillows Series 800 - Stearman PT-17 (698) Guillows Series 2000 - B-29 Super Fortress (679) Guillows Series 800 - Sopwith Camel (661) Guillows Series 500 - P-40 Warhawk (612) Molt Models Tyro (601) Guillows Series 400 - P-40 Warhawk (553) Guillows Series 1000 - F4U Corsair (522) Guillows Series 200 - Fokker DR-1 Triplane (505) ... View All Aircraft Top Six Manufacturers : Guillows Scratch Built Dumas Dave Diels Engineering, Inc Comet ManzanoLaser ... View All Manufacturers

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (3314 in total) :  <<   202   203   204   205   206  [ 207 ]  208   209   210   211   212   >>  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview edbecky Guillows Fokker D-VII Build 15-Apr-20 09:39 Views : 645 This was a really hard build for me due to it's size.. Southborough_man Guillows Series 400 - P-51 Mustang Build 14-Apr-20 14:53 Views : 869 Did two easiest surfaces with new (to me) Eze Dope BriandKilby Guillows Series 500 - Hawker Hurricane Build 13-Apr-20 11:48 Views : 381 tissued and doped! BriandKilby Guillows Series 500 - Hawker Hurricane Build 13-Apr-20 11:47 Views : 418 edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 09:26 Views : 382 I’ve also covered and doped the wings, ailerons, rudder, upper and lower elevators and upper horizontal stabilizer. Using EZ-Dope, I found that a 2:1 Dope to Water mixture worked best for applying and sealing the tissue. Thin enough to apply and work without globs, but thick enough to stick the tissue and fill in the pores. It still took between five and seven coats to get them completely sealed though. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:58 Views : 357 Evan my cat Chuck got into the act. She usually doesn’t care about this stuff, but I guess today, curiosity got the best of her! Hangar Aircraft Category Date Preview edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:57 Views : 392 The bottom. I left a section open where the wing spars pass through the fuse. I'll fill that in during assembly. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:56 Views : 327 The back edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:56 Views : 341 From the front edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:55 Views : 342 I’ve been busy over the last couple of weeks working on the Hannover. I 3D modeled and printed the cockpit combing. I used my FDM (Fused Deposition Modeling) printer with ABS plastic, instead of my DLP printer that I used for the interior parts. The FDM printer only has a resolution of 300 microns instead of 50, but for something as big as the combing, the high resolution isn’t as important. Plus the ABS is much more flexible and sandable, which is important since there are slight imperfections in the fuse I was able to accommodate by flexing the combing. I printed it in four parts, glued them together, sanded and filled as needed. Since this is ABS plasitc, I can use standard plastic model glues and fillers. The combing is attached to the previously sheeted fuse using thin and thick CA and kicker. Once set, I used Lightweight spackling to fill and sand. NATOMike Guillows Series 800 - Stearman PT-17 Parked 13-Apr-20 08:33 Views : 513 My next attempt at a Bi-Plane,. NATOMike Guillows Series 800 - Stearman PT-17 Build 13-Apr-20 08:32 Views : 519 Page (3314 in total) :  <<   202   203   204   205   206  [ 207 ]  208   209   210   211   212   >>  [ < Prev ] [ Next > ]