| Hangar |
Aircraft |
Category |
Date |
Preview |
| edbecky | Guillows Series 800 - B-25 Mitchell | Build | 27-Mar-20 13:11 |  | | Views : 3969 | | On the piano for display with a couple of paint touch-ups still to do. |
| biplane guy | Guillows Series 200 - SE5a | Parked | 26-Mar-20 18:51 |  | | Views : 4422 | | Adjustable windscreen |
| biplane guy | Guillows Series 200 - SE5a | Parked | 26-Mar-20 18:48 |  | | Views : 4278 | | Landing gear |
| Don C | Scratch Built Basler BT-67 | Build | 25-Mar-20 19:53 |  | | Views : 826 | | Windows are all that's left. |
| Don C | Scratch Built Basler BT-67 | Build | 25-Mar-20 19:52 |  | | Views : 769 | |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:48 |  | | Views : 732 | | I also modeled and printed all the parts for the interior. Parts include: Seat, fuel tank, yoke, radio, radio antenna spool, camera, camera plate holder, fuel pump, rudder bar, rudder bar firewall insets, three switches for the dash. |
|
| Hangar |
Aircraft |
Category |
Date |
Preview |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:43 |  | | Views : 665 | | Rear power take-off, many rocker arms and coolant pipes |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:42 |  | | Views : 736 | | Intake and Exhaust Manifolds and magnitos |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:41 |  | | Views : 686 | | Cylinders and Carbs |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:41 |  | | Views : 690 | | Argus III engine block assembled. I needed to do some filler in the front where the 3D print partially failed. |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:40 |  | | Views : 823 | | Been a trying time over the last few weeks. Working from home and social isolation has been challenging. But fortunetly, my family, friends and myself are healthy. I hope all the same for you! I have had some time (more time actually) to do some 3D printing. Here is the 3D print job for an 1/16 scale ARGUS (Opel) III six cylinder engine used in the Hannover CIIIa and serveral other German aircraft during WWI. I modeled this is Blender, then using my print pipeline, was able to print it out in five separate print jobs. Most of these only took 4 - 6 hours to print. Print time is proportial to the number of layers (hight in Z Axis) of the print, not the number of parts. I have found there tends to have more issues with lots of parts on one print, so I tend to keep the numbers smaller and do more prints. It took two weekends and a week of evenings to model the entire engine. However, now that I have it, I can print it in any scale I want down to about 1/24. Any smaller than that and I run into issues with parts being too small and would need to rework the model. |
| Don C | Scratch Built Basler BT-67 | Build | 22-Mar-20 18:44 |  | | Views : 675 | | Waiting to be attached. Alll's quiet up here in the mountains. Hope it's the same for the rest. |
|
