| Hangar |
Aircraft |
Category |
Date |
Preview |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 20-Jan-09 22:36 |  | | Views : 1762 | | I am pleased at the airbrushed seperation between upper and lower surfaces. The next step is a coat of Future. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 20-Jan-09 22:27 |  | | Views : 1734 | | The first coat of Tamiya paint airbrushed on. Upper surfaces are Japanese Navy Green over Japanese Navy Light Gray, both have been lightened with white (20%). |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 20-Jan-09 00:52 |  | | Views : 1832 | | The air intakes and scoops have been added and the fuselage insides of the intakes and the scoops have been painted black. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 20-Jan-09 00:43 |  | | Views : 1834 | | I painted interior of the air intakes and scoops black for depth. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 19-Jan-09 11:03 |  | | Views : 1885 | | Because the Shinden will be hanging from the ceiling I decided not to bother with a cockpit also research was very difficult to find. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 19-Jan-09 10:54 |  | | Views : 1758 | | Patterns for the wing to fuselage filets were not supplied and it took some cutting, fitting, and trimming to get them in position and then doped. I painted the interior of the air intakes black to provide depth. |
|
| Hangar |
Aircraft |
Category |
Date |
Preview |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 11-Jan-09 16:55 |  | | Views : 1899 | | The rear engine cowling. I cut out the cooling outets -- a little paint will make a big difference. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 11-Jan-09 16:47 |  | | Views : 786 | | The air scoops are shaped and had several coats of Aero Gloss Balsa Filler Coat and Filler and sanded. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 11-Jan-09 15:57 |  | | Views : 775 | | A trial fit of the plastic strip to see if it is right, I won't super glue it down until the wing is fitted, but before the the fuselage is papered. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 11-Jan-09 15:50 |  | | Views : 696 | | I superglued a strip of 1/64 plastic sheet to form thin edges of the air intakes. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 11-Jan-09 15:45 |  | | Views : 746 | | The fuselage, wings, and rudders are constructed, doped, and sanded. The engine cowling and nose cone have been added and shaped. |
| jerry campbell | Dave Diels Engineering, Inc Kit #10, Kyushu J7W1 Shinden | Build | 07-Jan-09 10:59 |  | | Views : 870 | | I usually have copies of the plans made so I can cut them apart, allowing me to work on small segments of the plans. |
|
