I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Aero-Werkes AW 11601 - Hannover CL IIIa View Details View All Switch Aircraft Users Aircraft edtherenderman LASTWOODSMAN

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (6 in total) :  1   2   3   4   5   6  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:56 Views : 322 From the front edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 13-Apr-20 08:55 Views : 324 I’ve been busy over the last couple of weeks working on the Hannover. I 3D modeled and printed the cockpit combing. I used my FDM (Fused Deposition Modeling) printer with ABS plastic, instead of my DLP printer that I used for the interior parts. The FDM printer only has a resolution of 300 microns instead of 50, but for something as big as the combing, the high resolution isn’t as important. Plus the ABS is much more flexible and sandable, which is important since there are slight imperfections in the fuse I was able to accommodate by flexing the combing. I printed it in four parts, glued them together, sanded and filled as needed. Since this is ABS plasitc, I can use standard plastic model glues and fillers. The combing is attached to the previously sheeted fuse using thin and thick CA and kicker. Once set, I used Lightweight spackling to fill and sand. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:53 Views : 361 Looking forward: This the observers station. The long focus camera is mounted with the lens looking through a access hole in the floor. The radio is on the left. On the upper right is a box that holds film cartridge. Each cartridge has six film plates that cycle through as each picture is taken. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:49 Views : 332 Looking aft: Here you can see the pilot's seat, yoke, fuel tank and seat belts. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:47 Views : 319 Engine isn't mounted yet. I still have a little more firewall detail to add. Gray box on the left is the ammo box. The Spandau Machine gun will mount above and to the left. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:45 Views : 310 Hangar Aircraft Category Date Preview edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:44 Views : 312 edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 31-Mar-20 08:44 Views : 308 Cockpit and observer sections of aircraft mostly complete. Most interior parts where 3D printed. however, the seat belts where done with sheet polystyrene and 22 gauge wire. All wood was stained with oak stain with a mat clear over the top. The camera frame and bracing above the pilots seat was created with soldered copper tubing. Parts where hand painted, then given a coat wash to age them. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 30-Mar-20 10:50 Views : 420 Closeup of rear rear bank of cylinders, carb and duel mags. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 30-Mar-20 10:49 Views : 331 Top view showing rocker arms. Each was individually printed and installed. Push rods are 22 gauge wire. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 30-Mar-20 10:48 Views : 299 Other side f engine with water input lines. Exhaust headers not installed. edtherenderman Aero-Werkes AW 11601 - Hannover CL IIIa Build 30-Mar-20 10:47 Views : 292 Argus III engine assembled and painted. Left side is thrust end. Page (6 in total) :  1   2   3   4   5   6  [ < Prev ] [ Next > ]