| Hangar |
Aircraft |
Category |
Date |
Preview |
| hjlittman | Guillows 25H-15 Vaught F7U Cutlass | Build | 20-Feb-13 21:03 |  | | Views : 1503 | | Not the Guillows Cutlass, but mine. I was at the O.F.F.C. (Old Farts Flying Club) meeting last week and was reminded that the contest, at the end of the month, was for no-cal pusher. It seemed that everyone there was practicing with a Hansa Jet from the A. A. Lidberg plans. Some others were talking about building a Shinden or an XP55. (Both plans are available, but I don't have the reference.) At first I wasn't going to participate, my time being what it is, then it occurred to me that an F7U-1 could work very well, and would be mildly disruptive, so I decided to see if I could draw and build one in about 4 hours. It's coming along nicely, squeezed in a few minutes at a time between other tasks, but I missed my O.F.F.C. meeting this morning and not having access to an indoor venue between now and the contest it will be a case of get it trimmed inside my den (13.5 foot ceiling) and go for broke at the contest next week. If it flies well it's another possibility for a kit. |
| hjlittman | Guillows Series 200 - Fokker DR-1 Triplane | Parked | 15-Jan-13 10:19 |  | | Views : 1335 | | Now tell me that this trend toward giant scale RC has not gotten out of hand. |
| hjlittman | Guillows Series 900 - Skyraider | Parked | 01-Dec-12 01:33 |  | | Views : 1341 | | Not quite finished, but "on the gear" |
| hjlittman | Guillows Series 900 - Skyraider | Parked | 01-Dec-12 01:32 |  | | Views : 1476 | | Magnetic "wheelwells" off wings. |
| hjlittman | Guillows Series 900 - Skyraider | Parked | 27-Nov-12 19:58 |  | | Views : 1298 | | I'm flying it "gear up" but wanted landing gear for display. I made some detachable "wheel wells" that are held on with rare earth magnets to a couple of small pieces of steel (cat food can lid) glued to the ribs under the covering. There is also a small piece of steel on the rear former to hold on the tailwheel and tailhook. The struts are wire wrapped with paper. They are not glued on to the "wheel wells" in the photo, but will be glued in after the back of the front strut covers and the struts have been painted. The square loops in the wires go around the magnets when they are glued in. Another piece of steel is under the middle of the fuselage for an intended Mk XIII torpedo. |
| hjlittman | Guillows Series 900 - Skyraider | Build | 27-Nov-12 19:58 |  | | Views : 1250 | | I did get a little farther along with the Skyraider. The nose block is finished with it's key. The flat plate nose block is a sandwich of 1/64" plywood, balsa and 1/64" plywood. The front of former 'A' is also faced with 1/64" plywood. Most people say this is unnecessary, but I have been flying my Typhoon, with a similar setup, for 8 years now. |
|
| Hangar |
Aircraft |
Category |
Date |
Preview |
| hjlittman | Guillows Series 300 - Piper Cub 95 | Parked | 11-Nov-12 12:44 |  | | Views : 2090 | | The definitive version of the indoor A-frame pusher. |
| hjlittman | Guillows Series 900 - Skyraider | Build | 18-Oct-12 13:41 |  | | Views : 1332 | | Sanded down, the filled area makes a better looking cowl anyway. |
| hjlittman | Guillows Series 900 - Skyraider | Build | 18-Oct-12 13:40 |  | | Views : 1344 | | The noses of the 900 series kits tend to be a little weak so I do a little fill in to make them stronger and easier to handle. |
| hjlittman | Guillows Series 900 - Skyraider | Build | 18-Oct-12 13:38 |  | | Views : 1276 | | am doing a 900 Series Skyraider for the "G" Challenge this year. The Skyraider has been on my small building board for some months but has been sidetracked by more pressing projects. Since there are only 14 days left in this year's "G" Challenge I figured that I had better get to it. Of course I know someone who builds his contest models the night before the contest, but that is another story. The wood in this kit is quite light but a tad on the brittle side. I had to sand the back sides of the sheets to get the parts out. And, even then I still had to do some cutting. Fortunately, the sheets containing the fuselage sides were approximately the same density and grain structure, so the fuselage went together straight without any trouble. |
| hjlittman | Guillows Series 300 - Piper Cub 95 | Build | 02-Aug-12 22:24 |  | | Views : 2628 | | The L-4 project tacked together for a "bones shot". The structure you see weighs 16 grams. I'm estimating 28 grams, covered and painted, less rubber. |
| hjlittman | Guillows Series 300 - Piper Cub 95 | Parked | 29-Jun-12 23:08 |  | | Views : 2205 | | I get my 21st Century tool set up and the first thing I build is a design from the 19th Century. Go figure! |
|
