I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Peck Polymers One Nite 28 View Details View All Switch Aircraft Users Aircraft scigs30 SteveM

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (4 in total) :  1   2  [ 3 ]  4  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview SteveM Peck Polymers One Nite 28 Flying 09-Mar-08 16:00 Views : 677 High altitude fly over. SteveM Peck Polymers One Nite 28 Flying 09-Mar-08 15:59 Views : 627 Just launched - starting to climb as it circles around. Flights are more smooth and not the jack rabbit jump out of the gate of a tightly wound rubber motor. SteveM Peck Polymers One Nite 28 Flying 09-Mar-08 15:57 Views : 719 Keep your rubber, lube, and winders. Just 3-4 minutes on the charger and it's ready to go. SteveM Peck Polymers One Nite 28 Build 08-Mar-08 23:16 Views : 791 Ready to fly at the park tomorrow if I can get there before the rain does. Weight is 91.7 grams, 30 grams heavier than on rubber power. SteveM Peck Polymers One Nite 28 Build 08-Mar-08 23:15 Views : 822 KP-01 motor is retained with three 2-56 nylon screws. The holes were drilled and taped, a little thin CA wicked into the wood, then taped again. SteveM Peck Polymers One Nite 28 Build 08-Mar-08 23:13 Views : 803 3x110 mAh NiCd and 5 amp fuse (goes into the yellow socket) acts as a switch. Fuselage also had 4" cut off of the front. Hangar Aircraft Category Date Preview SteveM Peck Polymers One Nite 28 Flying 08-Mar-08 18:36 Views : 716 These flights are all done with hand winding as the winder broke and CA wouldn't hold it together. I managed to get some 15-20 second flights and then decided my poor wrist and finger were tired of winding and it was time for electric FF conversion. SteveM Peck Polymers One Nite 28 Flying 08-Mar-08 18:33 Views : 711 Went to the park today and tried the One Nite 28 with rubber powered FF. SteveM Peck Polymers One Nite 28 Build 07-Mar-08 15:46 Views : 779 I have been weighing my battery options. The KP-01 motor needs 3.6 volts while the RC receiver will need 4.8-6 volts. The LiPo is 4.4g, NiCd pack is 24.8 g, and NiMh pack is 34.1g. I either need to use two battery packs build a regulator for the motor. SteveM Peck Polymers One Nite 28 Build 06-Mar-08 13:01 Views : 735 Made in China? Nope, soldered right here in the USA with pride and not quite enough solder (note the orange wire). It's a Pixie-7P that I was going to use to provide some sort of motor control when I convert the One Nite 28 to electric RC. SteveM Peck Polymers One Nite 28 Flying 03-Mar-08 14:18 Views : 831 Crocuses are the other sign that spring is on the way, these were right next to the daffodils. SteveM Peck Polymers One Nite 28 Parked 03-Mar-08 01:20 Views : 856 Ready for rubber powered FF. Final weight is 64 grams but landing wheel can be removed to save 2.5 grams. This is kit tissue covered with crystal clear. Page (4 in total) :  1   2  [ 3 ]  4  [ < Prev ] [ Next > ]