I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Scratch Built Loening OL-8 Amphibian View Details View All Switch Aircraft Users Aircraft rayl Skyediamonds1985

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (14 in total) :  <<   7   8   9   10   11   12   13   14  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview rayl Scratch Built Loening OL-8 Amphibian Reference 28-Dec-15 23:41 Views : 553 Poppy: Here's a good shot at the Duxford Museum. rayl Scratch Built Loening OL-8 Amphibian Reference 22-Dec-15 11:45 Views : 533 Merry Christmas to All! Happy landings in the New Year. rayl Scratch Built Loening OL-8 Amphibian Reference 28-Aug-15 20:00 Views : 570 Hey y'all, I'm back. Short tale of woe: I cut out all of teh ribs and wing parts for the Loening last week, the found that I had used the 1/16 scale set of plans instead of the 1/12 scale. Disgusted is putting it mildly. While recovering from that Faux Pau, I decided to utilize my new minuature Lathe to whip ot a Boeing Delta II Launch Vehicle that carried teh Mars Rover "Spirit" to the Red Planet. So with James (and the general populace's approval) I will turn my corner of the site into the "Virtual Aero(space) Drome" for a while. [James if you could add "Delta II No. 298" to the scratchbuilt cagegory? rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:11 Views : 608 Whatdaya think? rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:11 Views : 612 This about where they will be when I get them mounted on the L/G, which will be wole other story. rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:09 Views : 495 Tire material: before and after. This a piece of vacuum hose from teh atuomotive store. You can also use foam filler rod. I cut the tubing just a LITTLE shorter than the teh circumference of the rim and used gell superglue and held it together for a minute until the CA set-up. I snaded the whole tire down with 100 grit papaer then use my Dremel tool with a coarse scotch-brite wheel to buff it all to the same appearance. Hangar Aircraft Category Date Preview rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:03 Views : 492 It even goes round-n-round! rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:02 Views : 527 All done. Note the offset of the rim holes as I mentioned earlier. rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 16:01 Views : 499 Working on the top side with the wire all tangled up. I found that you should take time to un-tangle the wire about every three holes. Also, as John O intoned, MAKE SURE that the length of the piece of the spoke material is long enough!!! (40 spokes) X (1 1/8 radius) = 50 inches. I added 10 inches for a comfort factor. rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 15:57 Views : 504 here the bottom side is done, starting on the top side. rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 15:56 Views : 441 Starting to weave the spokes. Do the lower side first. Note that when I drilled the holes in the rim, I offset thealternating holes by about the with of my drill bit to allow for full access to the holes as the weaving progresses. ANother nice thing about this jig is that you can offset the hub to either side of center to replicate wheels that have offset spokes in real life. The toothpick (lower right) is jambed into the last filled spoke hole to maintain the tension as the weave progresses. rayl Scratch Built Loening OL-8 Amphibian Build 21-Jun-15 15:51 Views : 447 Completed hub. In this instance I used a 1/2" long piece of 1/8" ID Evergreen tubing. Page (14 in total) :  <<   7   8   9   10   11   12   13   14  [ < Prev ] [ Next > ]