| Hangar |
Aircraft |
Category |
Date |
Preview |
| kenm94591 | Dumas Kit #223, P-26 Peashooter | Parked | 20-Mar-19 15:59 |  |
| Views : 325 |
| Three of the bad crankcases. Total of six before I got the one that was correct. Turns out I need to go back to grade school to leaarn how a protractor works. |
| kenm94591 | Guillows Series 500 - Hellcat | Parked | 19-Mar-19 17:14 |  |
| Views : 605 |
| Well finally have all nine of the cylinders for the P-26 glued up. I added the "headers" then painted everything black. I think I am going with the silver highlights for the cylinders. Now to get a good crankcase cut so I can start the assembly. |
| kenm94591 | Dumas Kit #223, P-26 Peashooter | Parked | 17-Mar-19 13:56 |  |
| Views : 394 |
| The unpainted push rods for the engine of the P-26. The rods are 3/32" brass rods and the connectors at each end are heat shrink tubing. The longer tubing go to the top and the shorter goes to the bottom of the push rods. The top is made from 5/64" heat shrink tubing that has been shrunk and is tight and cannot be moved. The bottom is made from 3/32" heat shrink tubing that was shrunk and then cut into small sections. Because it is 1/64" larger than the top tubing it can be slid on and off the brass rod. I will glue the top to the engine header and after it dries slide the bottom piece into place and glue. At the scale I am working that little play allows for a tight fit. I will touch up the paint after the glue dries. |
| kenm94591 | Dumas Kit #223, P-26 Peashooter | Parked | 16-Mar-19 20:47 |  |
| Views : 473 |
| This is a very rough protopye to check the look and build of one of the nine cylinders or the Wasp engine. The "crankcase" is one inch in diameter with nine flats for each of the cylinders. Start by drilling a hole and inserting small bamboo rod and then inserting a small piece of coffee stirrer over that. The set screw is then glued in place and the other two set screws are glued to the cylinder. Half round styrene rod is uesd for the headers. 3/64" carbon steel music rod is used for the push rods. Will not be using that on the actual build. 3/16" strips of masking tape is used at the top and bottom of the push rods to replicate the connectors to the crankcase and headers. Masking tape will not be used for final motor. I am having trouble trying to build the spark plugs as they are 1/16" long and 1/64" round. |
| kenm94591 | Dumas Kit #223, P-26 Peashooter | Parked | 15-Mar-19 16:56 |  |
| Views : 521 |
| So my wife dug out the scroll saw and rough cut the crank case for the P-26. She then filed everything down to just above the black line (note to self - basswood is hard). jBecause of my eyesight and shakey hands my wife helped. Now I have to sand down to the black line. Not sure which color to use for the engine. Left to right I have brass, steel or black. |
| kenm94591 | Dumas Kit #223, P-26 Peashooter | Parked | 14-Mar-19 19:15 |  |
| Views : 309 |
| I have a Dremel and the Dremel work station so I chucked up a cutoff wheel set it to the heigth I wanted. Was able to push and turn the pipe so I got it cut to the proper length. Left side is before cutting. Center is the result of cutting. Right side is c coffee lid with and without center cut out. Turns out a coffee lid fits the new cowl perfectly and has a lip on it which I am hoping I can use it to provide the correct profile. |
