| Build Thread, Page :
1 [ 2 ] 3 (49 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
| John M Oshust, Comment for image # 16504 | 20 Feb 10 09:53 |
| Nice job Tony. Dejavu all over again! |
| wingspanner, Image # 16504 | 20 Feb 10 09:40 |
Fuselage covered. Wing attached and now for the fillets |
| wingspanner, Image # 16503 | 20 Feb 10 09:38 |
from the inside... |
| wingspanner, Image # 16502 | 20 Feb 10 09:37 |
Wings attached with a dowel and bolt |
| wingspanner, Image # 15999 | 21 Jan 10 02:22 |
Templates supplied help with the sheeting. |
| wingspanner, Image # 15978 | 20 Jan 10 01:39 |
started sheeting the fuselage |
| wingspanner, Comment for image # 15965 | 19 Jan 10 14:50 |
| Thanks for the advice. I hadn't set up the throws yet. All advice is great as I'm still a beginner in RC
|
| pfinn, Comment for image # 15965 | 19 Jan 10 13:55 |
| You may wish to move the position of the push rod connectors on the servo head inboard a couple holes for your inital flights, unless you have dual rates on your transmitter. Set up like this, it may be a bit "Touchy" in flight. The instructions should have aileron throw measurements. |
| wingspanner, Image # 15966 | 19 Jan 10 01:03 |
As viewed from wingtip when bolted |
| wingspanner, Image # 15965 | 19 Jan 10 01:02 |
An ingenius method for controling wing surfaces. I hope i have it right! |
| wingspanner, Image # 15964 | 19 Jan 10 01:01 |
bolted from underneath this will be sheeted with formers later |
| wingspanner, Image # 15963 | 19 Jan 10 01:00 |
bolt to fasten wings to fuselage |
| wingspanner, Image # 15886 | 14 Jan 10 11:09 |
The wings fasten into the fuselage with a plastic bolt. The timber down the centre is a jig that holds the formers in place when the stringers are attached. |
| wingspanner, Image # 15885 | 14 Jan 10 11:07 |
Wings glued with a strip of fibreglass to strengthen down centre.Two wires in centre control the wing surfaces. These will be attached to a servo which will be cut and glued into the fron of the wing. |
| John M Oshust, Comment for image # 15725 | 05 Jan 10 04:07 |
| Very similar to the plans for my Rat...nice job. |
| wingspanner, Image # 15727 | 05 Jan 10 02:00 |
Sheeted then seperated |
| wingspanner, Image # 15726 | 05 Jan 10 01:59 |
Wings and ailerons are attached until last minute. |
| wingspanner, Image # 15725 | 05 Jan 10 00:09 |
Back section is attached to fuselage and front section bolts onto back via access from vents at front |
| wingspanner, Image # 15724 | 05 Jan 10 00:07 |
Had to extend the cowl by1/4" to allow the motor to fit. Ive made the cowl removable with the motor attached to the fuselage. |
| wingspanner, Comment for image # 15674 | 31 Dec 09 12:27 |
| It all slides out through the front.(Formers get smaller the further back you go.)
|
| Build Thread, Page :
1 [ 2 ] 3 (49 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
