| Build Thread, Page :
1 [ 2 ] 3 (43 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
| lennyz, Image # 2619 | 02 Apr 07 23:23 |
assembled & covered from the nose |
| lennyz, Image # 2618 | 02 Apr 07 23:22 |
Tailfeathers w/notches for moveable control surfaces |
| jgood, Comment for image # 2468 | 01 Mar 07 18:56 |
| It's a 400 series kit now. |
| cdwheatley, Comment for image # 2468 | 01 Mar 07 16:56 |
| The 900 series kits, especially the fuselage, are built up in a completely different way to the 400s. |
| lennyz, Comment for image # 2473 | 01 Mar 07 09:37 |
| FOUND OUT YELLOW GLUE- WHICH I USED ON THE REST OF THE MODEL
WILL NOT HOLD HERE--CA GLUE WORKS GREAT. ALSO ALUMINUM STRIPS WILL BREAK UPON REPEATED BENDING-BUT ONCE I FIND THE RIGHT TRIM-THERE THEY'LL STAY |
| jgood, Comment for image # 2468 | 28 Feb 07 13:29 |
| I'll switch you over to a 400 series Mustang tonight Lenny. |
| lennyz, Comment for image # 2468 | 28 Feb 07 11:41 |
| AFTER A QUICK CHECK YOU ARE ABSOLUTELY CORRECT!!!!
I HAVE HAD A VERY SENIOR MOMENT-DON'T KNOW WHERE I MIXED IT UP. BESIDES SCALE SIZE WHAT DIIFERNCES ARE THERE? |
| cdwheatley, Comment for image # 2468 | 28 Feb 07 09:18 |
| This IS a 400 series kit flyguy72. I have a 900 series Mustang and it's nothing like this - I think lennyz must have had a senior moment! Nice work though lennyz |
| lennyz, Comment for image # 2468 | 28 Feb 07 09:10 |
| JUST FOR REFERENCE-THOSE ARE 1" SQUARES IN THE BACKGROUND
NOTICE THE BEND AT THE REAR OF THE FUSELAGE? THATS THE REASON I'M TRYING TO MAKE MOVEABLE SURFACES--FLIGHT TRIM |
| flyguy172, Comment for image # 2468 | 27 Feb 07 23:41 |
| sure it's a 900 series? looks like a 400 to me. great job though! love the removable landing gear idea! |
| jgood, Comment for image # 2469 | 27 Feb 07 20:33 |
| Looks good Lenny. Nice documentation of your build! |
| lennyz, Image # 2479 | 27 Feb 07 19:53 |
LANDING GEAR WIRE INSTALLED IN RECEPTACLE |
| lennyz, Image # 2478 | 27 Feb 07 19:52 |
1/16" AIRLINE FERRULE USED FOR BRASS TUBE ON LANDING GEAR-THIS MAY ALSO MAKE A GOOD BEARING FOR PROP |
| lennyz, Image # 2477 | 27 Feb 07 19:50 |
LANDING GEAR WIRE PER PLAN EXCEPT FOR TOP-90DEGREE BEND SLIDES INTO TUBE AND NOTCH ON RECEPTACLE |
| lennyz, Image # 2476 | 27 Feb 07 19:49 |
LOWER VIEW-NOTCH HOLDS LANDING GEAR WIRE FOR DISPLAY |
| lennyz, Image # 2475 | 27 Feb 07 19:48 |
TOP VIEW OF LANDING GEAR RECEPTACLE-LEADING EDGE SCRAP SANDWICHED WITH 1/16" SCRAP AND TUBE IN MIDDLE |
| lennyz, Image # 2474 | 27 Feb 07 19:46 |
BLOCK BEHIND LEADING EDGE ARE RECEPTACLES FOR REMOVABLE LANDING GEAR |
| lennyz, Image # 2473 | 27 Feb 07 19:45 |
STRIPS OF POP CAN FOR HINGES-HOPE THEY HOLD ADJUSTSMENTS FOR FREE FLIGHT |
| lennyz, Image # 2472 | 27 Feb 07 19:44 |
RUDDER WITH EXTRA STRINGER AND HINGES IN PLACE FOR MOVEABLE TAIL SURFACE |
| lennyz, Image # 2471 | 27 Feb 07 19:43 |
ELEVATOR WITH EXTRA STRINGER AND HINGES FOR ELEVATOR IN PLACE |
| Build Thread, Page :
1 [ 2 ] 3 (43 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
