| Build Thread, Page :
1 2 [ 3 ] 4 (75 posts, 20 posts per page, 4 pages in total)
|
[ < Prev ] [ Next > ] |
| Don C, Comment for image # 37514 | 14 Dec 16 12:39 |
| But the right plane. A work of art! |
| rgood, Comment for image # 37514 | 14 Dec 16 12:36 |
| Sorry - in wrong folder! |
| rgood, Image # 37514 | 14 Dec 16 12:35 |
.....made a start on the 3D effect. |
| rgood, Comment for image # 37505 | 14 Dec 16 11:32 |
| Photo panel! James did that for me. I will now fabricate yokes, throttle and mixture knobs - to give a 3D effect. |
| David Duckett, Comment for image # 36529 | 14 Dec 16 00:47 |
| Yeah:-) |
| Skyediamonds1985, Comment for image # 37505 | 13 Dec 16 20:29 |
| Real panel, or photo of the real panel? Looks so good. |
| Skyediamonds1985, Comment for image # 37505 | 13 Dec 16 20:28 |
| rgood, this is an amazing work of art! I could also see the fabricated small instrument light shades on the upper left corners of some of the instruments. Outstanding! The Vernier red colored mixture and circuit breakers along with the carbon monoxide card are great. You've done it all. Hope you took pictures of the build. |
| John M Oshust, Comment for image # 36515 | 13 Dec 16 20:10 |
| I have had great success with Al duct tape. In fact anything I have covered with Al is duct tape. |
| rgood, Comment for image # 36515 | 13 Dec 16 19:00 |
| That tooling aluminium sounds interesting CW! I will look out for that, thanks. |
| Creosotewind, Comment for image # 36529 | 13 Dec 16 17:22 |
| Instead of reading j-to, I read J-Lo. And entirely different thing altogether. |
| Creosotewind, Comment for image # 36515 | 13 Dec 16 17:21 |
| You might want to check out tooling aluminum from an art supply store. A bit thicker, but can easily be cut and shaped to conform. You can also use a pounce wheel to create "rivets". The cowling on my Piper Cub was that material. |
| Huey V77, Comment for image # 37505 | 13 Dec 16 13:52 |
| Need a condition inspection, call me! |
| John M Oshust, Comment for image # 37505 | 13 Dec 16 11:46 |
| Very nice. I see you have included the customery "muffler bearing cutoff switch"! |
| rgood, Image # 37505 | 13 Dec 16 11:16 |
Panel is prepared for the Ercoupe. |
| Huey V77, Comment for image # 36529 | 09 Aug 16 07:08 |
| That's what I ment JATO. |
| David Duckett, Comment for image # 36529 | 09 Aug 16 05:37 |
| The acronym is JATO. |
| rgood, Comment for image # 36529 | 08 Aug 16 23:54 |
| J-to was that rocket assisted take-off? |
| rgood, Comment for image # 36529 | 08 Aug 16 23:53 |
| James' Ercoupe (N94805) has rudder pedals - I will try to fit them into my model as this is to be a copy of that aeroplane - it is difficult, sometimes, to draw the line when doing detail work! |
| Huey V77, Comment for image # 36529 | 08 Aug 16 19:37 |
| Rgood that's looking very nice, you know they used it for j-to testing. Rudder peddles or on ? |
| rgood, Comment for image # 36515 | 08 Aug 16 15:29 |
| I have done a small "test" of using kitchen foil as a covering for balsa - it took quite well and the finish is very near to polished alloy but it is quite prone to damage from finger nails etc - we will see, may have to re-think that one! |
| Build Thread, Page :
1 2 [ 3 ] 4 (75 posts, 20 posts per page, 4 pages in total)
|
[ < Prev ] [ Next > ] |
