I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Top Ten Aircraft : (numbers in brackets represent number of images online) Guillows Series 400 - P-51 Mustang (953) Guillows Series 200 - SE5a (941) Guillows Series 800 - Stearman PT-17 (698) Guillows Series 2000 - B-29 Super Fortress (679) Guillows Series 800 - Sopwith Camel (661) Guillows Series 500 - P-40 Warhawk (612) Molt Models Tyro (601) Guillows Series 400 - P-40 Warhawk (553) Guillows Series 1000 - F4U Corsair (522) Guillows Series 200 - Fokker DR-1 Triplane (505) ... View All Aircraft Top Six Manufacturers : Guillows Scratch Built Dumas Dave Diels Engineering, Inc Comet ManzanoLaser ... View All Manufacturers

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (3313 in total) :  <<   3056   3057   3058   3059   3060   3061   3062   3063   3064   3065   3066   >>  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview David Duckett Guillows Series 800 - B-25 Mitchell Build 16-Jun-07 10:31 Views : 2360 Almost finished David Duckett Guillows Series 800 - B-25 Mitchell Build 16-Jun-07 05:42 Views : 1549 Props will be installed later this morning. David Duckett Guillows Series 800 - B-25 Mitchell Build 16-Jun-07 05:39 Views : 1469 moostang51 Guillows Series 2000 - B-24 Liberator Build 15-Jun-07 18:42 Views : 1371 Lots of trial fitting onto stabilizer before shaping but fit is perfect. Going to use the pre-built moveable rear rudder assemly and the cardboard overlays so panel lines can be used as per plan. Only thing, should have doped the stabilizer prior to multi moostang51 Guillows Series 2000 - B-24 Liberator Build 15-Jun-07 18:35 Views : 1374 New carved rudder. Starts as a 1/2 stock. First cut through notch for stabilizer then lots of shaping and sanding. Used the Guillows plan for final profile. jerry campbell Dave Diels Engineering, Inc Kit #43, Ki 84 Hayate "Frank" Build 15-Jun-07 15:28 Views : 958 I use small fuel line to simulate the landing gear. It is extremely flexible and slips easily onto the landing gerar wire after it is bent. I've now got to add strips fo masking take to simulate the hydraulic ridges. Hangar Aircraft Category Date Preview jerry campbell Dave Diels Engineering, Inc Kit #43, Ki 84 Hayate "Frank" Build 15-Jun-07 15:17 Views : 1269 The sleek shape of the "Frank" is finally taking shape. The Hayate (Hurricane) in the hands of an experienced pilot could out fly both the Musttang and Hellcat. jerry campbell Dave Diels Engineering, Inc Kit #43, Ki 84 Hayate "Frank" Build 15-Jun-07 15:09 Views : 1050 The engine cowling is built up with rings of balsa and was a bit of a job carvng and sanding to shape as well as cutting and shaping the air intake . You can see where the stringers must still be added to the fuselage. jerry campbell Dave Diels Engineering, Inc Kit #43, Ki 84 Hayate "Frank" Build 15-Jun-07 14:57 Views : 947 The major components are doped, sanded, and papered. The lower third of the fuselage will be papered after the wing has been added to the fuslelage and the l ower stringers are in place. jernst Dave Diels Engineering, Inc Kit #39, Aichi D3A1 "Val" Parked 15-Jun-07 13:55 Views : 1503 Diels Aichi D3A1 'Val'; 24 in span - with major wing panel 'flexing' under tissue compression jernst Dave Diels Engineering, Inc Kit #42, Curtiss P-40B/C Warhawk Parked 15-Jun-07 13:54 Views : 1614 Diels P-40B Warhawk; 18.5 in jernst Dave Diels Engineering, Inc Kit #40, Republic P-47N Thunderbolt Parked 15-Jun-07 13:52 Views : 1670 Diels Republic P-47N; 20.25 in Page (3313 in total) :  <<   3056   3057   3058   3059   3060   3061   3062   3063   3064   3065   3066   >>  [ < Prev ] [ Next > ]