| Build Thread, Page :
1 2 3 4 5 [ 6 ] 7 8 9 10 (188 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
| mark eggebeen, Image # 40806 | 09 Jan 19 13:23 |
Meanwhile....on a work bech not far away! |
| mark eggebeen, Comment for image # 40801 | 06 Jan 19 22:58 |
| the one at the Heritage Center was about 16 inches. this is
a download and made smaller to fit onto a 8 1/2 by 11
paper |
| rgood, Comment for image # 40801 | 06 Jan 19 11:50 |
| What wingspan is that Mark? Cute model. |
| mark eggebeen, Comment for image # 40801 | 05 Jan 19 16:22 |
| there is some serious detail work in these little buggers. |
| mark eggebeen, Image # 40801 | 05 Jan 19 16:21 |
Someone brought one of these into the Heritage Center last week. I tracked it down and found a free download |
| mark eggebeen, Comment for image # 40790 | 02 Jan 19 22:36 |
| thanks it's been quite project so far....I used to : build 'em fly'em crash 'em repeat |
| rgood, Comment for image # 40790 | 02 Jan 19 14:40 |
| A very well done balsa/plastic cross-over model - looking forward to the completion... |
| mark eggebeen, Comment for image # 40790 | 01 Jan 19 18:32 |
| Thanks. , that stuff is really thin .... |
| Don C, Comment for image # 40790 | 01 Jan 19 16:54 |
| That really looks good! Well done. |
| mark eggebeen, Image # 40790 | 01 Jan 19 11:50 |
after tearing off the tissue I glued the wings into the booms . then with gentle persuasion i slipped the sheets under the plastic and glued the sheets in place |
| rgood, Comment for image # 40773 | 21 Dec 18 11:51 |
| Nice one Mark! Best Wishes for Christmas and better year for all in 2019.
|
| Don C, Comment for image # 40773 | 21 Dec 18 11:42 |
| Thanks, Mark. And to you too.
|
| mark eggebeen, Image # 40773 | 20 Dec 18 17:44 |
Merry Christmas God Bless.... |
| David Duckett, Comment for image # 40739 | 14 Dec 18 02:30 |
| It's on this site. Look under "your hangar" for Poppy, then click on his name. |
| mark eggebeen, Comment for image # 40739 | 13 Dec 18 22:20 |
| sorry, still can't find him on that comet P-40 site
so far I have ripped off all the tissue and sanded the wings down to the bare balsa (mostly) I assume I use 1/32 sheets ? |
| David Duckett, Comment for image # 40739 | 13 Dec 18 16:02 |
| Poppy |
| mark eggebeen, Comment for image # 40739 | 13 Dec 18 15:22 |
| Can,’t find pappy on the -40 site6 |
| Don C, Comment for image # 40739 | 13 Dec 18 11:07 |
| It sounds like sanding is back in your life - gentle sanding. Poppy's Comet P-40 has a good explanation of sheeting wings. Good luck and have fun. |
| mark eggebeen, Comment for image # 40739 | 12 Dec 18 22:35 |
| part of the problem is that the wings are complete, with tissue, primer and finish ..Now I have changed my mind so
I'm kind of restricted in how to proceed |
| David Duckett, Comment for image # 40739 | 12 Dec 18 15:59 |
| If you want to sheet them you should check Poppy's hanger. |
| Build Thread, Page :
1 2 3 4 5 [ 6 ] 7 8 9 10 (188 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
