| Build Thread, Page :
1 [ 2 ] 3 4 (70 posts, 20 posts per page, 4 pages in total)
|
[ < Prev ] [ Next > ] |
| pfinn, Image # 12426 | 18 May 09 12:31 |
Chino airshow, yesterday. "Grumman" theme. |
| pfinn, Comment for image # 12393 | 16 May 09 16:50 |
| You know, some creative use of heat-shrink tubing would have been a whole lot easier and far less time consuming. Next time. Thanks though. |
| jgood, Comment for image # 12393 | 16 May 09 07:54 |
| Wow. Those turned pieces are amazing! |
| pfinn, Image # 12394 | 16 May 09 04:38 |
Boing, Boing, Boing. |
| pfinn, Image # 12393 | 16 May 09 04:35 |
LG dry fit. Big lumps of aluminum come off after the wheels are done. |
| jgood, Comment for image # 12373 | 15 May 09 09:46 |
| Ha! Nice response! The ole Eindecker isn't much bigger than my Moth. |
| pfinn, Image # 12375 | 15 May 09 01:53 |
All greased-up and ready roll for another fifty! |
| pfinn, Image # 12374 | 15 May 09 01:48 |
While machining more fittings for the EIII my little Mill decided to have a seizure. I have no idea how it got in where it was. Could have been in there for over fifty years! |
| pfinn, Image # 12373 | 15 May 09 00:56 |
Hey, "Good" idea. "Good" thing I just ordered a bigger motor and ESC. Mines lookin' a bit chunky! |
| pfinn, Comment for image # 12345 | 12 May 09 09:38 |
| Thanks all. Phil. |
| poppy, Comment for image # 12348 | 12 May 09 08:34 |
| Whoa!! A master machinist at play. |
| David Duckett, Comment for image # 12345 | 12 May 09 07:04 |
| Amazing! |
| jgood, Comment for image # 12345 | 12 May 09 06:53 |
| That's a beautiful little piece. |
| pfinn, Image # 12349 | 12 May 09 04:23 |
Three more to go. LG will articulate. |
| pfinn, Image # 12348 | 12 May 09 04:20 |
|
| pfinn, Image # 12347 | 12 May 09 04:18 |
A quick "How to". Again. |
| pfinn, Image # 12346 | 12 May 09 04:16 |
Axle rods: 10 degree droop, perpendicular to axis. Support rods: 25 degrees off vert, 4 degree sweep-back. Had to put the spike on... just because. Might be a theme starting here! Some thing to do with "Magnificent Men and..." |
| pfinn, Image # 12345 | 12 May 09 04:09 |
Making CF LG. Machining up some fittings. .032" CF rod (steel shown because the CF rods weren't round), aluminum fittings. |
| pfinn, Image # 12315 | 11 May 09 13:03 |
Fuse sides. Replaced 1/16" sheet with vert. grain 1/32". .015" Bass reinforcment strips. Longerons also capped with .010" Bass. Starting to wonder why I bought a kit! |
| pfinn, Image # 12314 | 11 May 09 12:57 |
Vert. and horz. stabs. .032" CF rod thru for "Give" during unforseen impact (or trample) with immobile objects. |
| Build Thread, Page :
1 [ 2 ] 3 4 (70 posts, 20 posts per page, 4 pages in total)
|
[ < Prev ] [ Next > ] |
