| Build Thread, Page :
1 [ 2 ] 3 (50 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
| jerry campbell, Image # 19278 | 18 Sep 10 10:46 |
The tail wheel, the arial mast, the exhausts are finished and the canopy is masked. |
| jerry campbell, Image # 19277 | 18 Sep 10 10:43 |
The gunsight and a decal from the spares box adds a little to an otherwise rather sparse interior. |
| jerry campbell, Image # 19276 | 18 Sep 10 10:41 |
Adding a gunsight above the instrument panel. |
| jerry campbell, Comment for image # 19255 | 15 Sep 10 04:06 |
| Another coat of Tamiya Cockpit Green has has been added to cover the dried dope and the top of the cockpit back. |
| FLYBOYZ, Comment for image # 19255 | 14 Sep 10 20:20 |
| whoow!cool stuff |
| jerry campbell, Image # 19255 | 13 Sep 10 14:15 |
I couldn't resist adding a bit of a sest and some seat harness. |
| jerry campbell, Image # 19254 | 13 Sep 10 14:13 |
|
| jerry campbell, Image # 19253 | 13 Sep 10 14:11 |
The wings elevator, rudder, spinner and canopy have been masking taped into position for trial fits. So farn so good. |
| jerry campbell, Image # 19252 | 13 Sep 10 14:07 |
The tissue has been added and three coats of dope have been applied. |
| Richardsk, Comment for image # 19205 | 13 Sep 10 06:47 |
| Here's a link to the Wikipedia article on the Bloch 150 to 152 series.
http://en.wikipedia.org/wiki/Bloch_MB.150
It looks as though it may be difficult to find references with French markings. I'll look through my references and see if I can find anything. |
| jerry campbell, Comment for image # 19205 | 13 Sep 10 04:02 |
| Thanks bsadonkill, I will try try it, now I got to find some decals to fit, I would rather not use German markings to picture a captured a/c if I can find some French markings. |
| bsadonkill, Comment for image # 19205 | 13 Sep 10 03:26 |
| You can make copies of your patterns on a copy machine. Then to transfer, place the copy face down on the wood.Use dope thinner to dampen a rag.Rub the damp rag on the back side of the copy.The dope thinner will melt the toner and transfer it to the wood.Don't get the rag too wet your transfer's will be runny.I used this methed when i built my Diels o-47, theirs a picture of the sheet i did transfers on next to the fuselege.Try it, it works. |
| jerry campbell, Comment for image # 19205 | 12 Sep 10 14:55 |
| HELP!I purchased the plans for a 1/24th scale Bloch 152 that there is no kit for. The plans have drawings of all the parts. Can anyone give me a tip on how you transfer the printed parts on to balsa sheets to make printwood so I can cut out the parts and build it. |
| jerry campbell, Image # 19205 | 10 Sep 10 00:29 |
Fitting the componet parts together before tissue it is starting to look a lot like a Hurricane. |
| jerry campbell, Image # 19204 | 10 Sep 10 00:26 |
I added a little detail to ome parts. The exhaust stacks are kit parts with plastic tubing in stead of straws.The under belly radiator is detailed with plastic screen and a bit of plastic tubing. The seat is balsa with a plastic sheet back. to the spinnerI added a disc of balsa for strength. |
| jerry campbell, Image # 19203 | 10 Sep 10 00:19 |
I filled the nose with balsa. |
| jerry campbell, Image # 19202 | 10 Sep 10 00:16 |
I added wood to the wing leading edges for both strength and as a base for attaching tissue, as well as looking better. |
| jerry campbell, Image # 19201 | 10 Sep 10 00:13 |
I usually block in the wing tips which not only look better but are easier for papering. |
| jerry campbell, Image # 19200 | 10 Sep 10 00:10 |
Seperating the rudder was easily done. |
| jerry campbell, Image # 19199 | 10 Sep 10 00:08 |
Construction on the building plans sheet was straight forward. |
| Build Thread, Page :
1 [ 2 ] 3 (50 posts, 20 posts per page, 3 pages in total)
|
[ < Prev ] [ Next > ] |
