Build Thread, Page :
1 2 3 4 [ 5 ] 6 7 8 (144 posts, 20 posts per page, 8 pages in total)
|
[ < Prev ] [ Next > ] |
Xanadu, Comment for image # 10815 | 12 Feb 09 20:47 |
Took me a few minutes of thinking before I finally had a good idea of it.
|
frwyflyer, Comment for image # 10815 | 12 Feb 09 10:15 |
I am very impressed with your building jig. Very creative for a model this large |
Xanadu, Image # 10815 | 11 Feb 09 21:59 |
|
Xanadu, Image # 10814 | 11 Feb 09 21:58 |
Side 2! |
Xanadu, Image # 10813 | 11 Feb 09 21:58 |
|
Xanadu, Comment for image # 10809 | 11 Feb 09 20:20 |
Wood glue, carpenter style, with #4 x 1/2 screws. They look like #10 in the pics, but they are not. |
moostang51, Comment for image # 10809 | 11 Feb 09 17:34 |
Epoxy for adhesive? Maybe some flathead #10's wood screws countersunk with epoxy in the hole so you can leave 'em in and cover right over. Looks sweet, BIG, but sweet. |
Xanadu, Image # 10811 | 10 Feb 09 22:23 |
|
Xanadu, Image # 10810 | 10 Feb 09 22:20 |
|
Xanadu, Image # 10809 | 10 Feb 09 22:19 |
Got it! Was much easier than I anticipated.......some hot water and away we go! |
moostang51, Comment for image # 10806 | 10 Feb 09 17:58 |
Kerfing might work, but with only a 3 lam plywood, you'd probably have to dampen the kerfed side also as the graining in a hem or doug fir veneer is pretty rigid at the color variations and a stepped effect might occur at the glue points. I would have cut the ply cross grain and it probably wouldve bent much easier, No kerfing just moisten the backside, apply CA and clamp. |
Creosotewind, Comment for image # 10806 | 10 Feb 09 12:59 |
You might try kerfing the inner portion, cutting a series of vertical slots on the back side, about 3/4 of the way through. Enough slots will allow the wood to flex so you can manipulate it into position. |
Creosotewind, Comment for image # 10773 | 10 Feb 09 12:56 |
You know, most guys pin their wood to the building board. I see you are using screws! The wingspan scales out to about 1/6 scale, so you can use a GI Joe for the pilot. |
Xanadu, Comment for image # 10806 | 09 Feb 09 21:17 |
See the bottom wing former........gotta figure a way to bend/twist the plywood without breaking it so I can fasten it down to b3,4,&5. Easy enough to do with a 3/32 piece of balsa, but a bit tricky with 1/4" plywood.
Maybe get the steam kettle out and hold it under where I need to flex. |
Xanadu, Image # 10806 | 09 Feb 09 21:12 |
|
David Duckett, Comment for image # 10803 | 09 Feb 09 19:13 |
No balls, no glory! |
Xanadu, Comment for image # 10804 | 09 Feb 09 15:47 |
Short............? I mean "shot" of course using my cell phone camera. |
Xanadu, Image # 10805 | 09 Feb 09 15:45 |
Starting the fuelage, waiting for the wing to dry enough to sand it. |
Xanadu, Image # 10804 | 09 Feb 09 15:43 |
Guess who....? My arm is not long enough to get a fullsize short of myself with my cell phone. |
Xanadu, Image # 10803 | 09 Feb 09 15:42 |
Maybe I should just bolt it onto my trucklid, and have a fancy schmancy race type car! |
Build Thread, Page :
1 2 3 4 [ 5 ] 6 7 8 (144 posts, 20 posts per page, 8 pages in total)
|
[ < Prev ] [ Next > ] |