| Build Thread, Page :
1 2 [ 3 ] 4 5 (95 posts, 20 posts per page, 5 pages in total)
|
[ < Prev ] [ Next > ] |
| Don C, Comment for image # 35615 | 20 Feb 16 10:26 |
| OK, I see it. Usually when I do that a chunk of the stringer stays with my finger. |
| Skyediamonds1985, Comment for image # 35615 | 20 Feb 16 10:03 |
| Looks very good. Your workmanship really shows. Very nice and precise. Lots of attention to detail. |
| lukebozek1, Comment for image # 35615 | 20 Feb 16 09:59 |
| This is one clean build. Great work. |
| pfinn, Comment for image # 35615 | 20 Feb 16 00:30 |
| Thanks guys.Don C, the third 1/16" stringer up from the 1/8" x 1/16".It's the brighter one. Comes off the foremost bulkhead not quite square. I think I glued my finger to it and while "Rolling" off my finger, I tweaked it a bit and there it stayed. Maybe I'll leave it as a lesson. ;) |
| Don C, Comment for image # 35615 | 19 Feb 16 11:06 |
| Looking forward to seeing this covered. Not sure what has to be adjusted though. It must be one of those things that stands put to the builder, but no one else notices unless you point it out. It's really nice. |
| jgood, Comment for image # 35614 | 19 Feb 16 09:42 |
| Looks amazing, Phil. |
| rayl, Comment for image # 35614 | 18 Feb 16 19:27 |
| Damn, that's looking good! |
| pfinn, Image # 35615 | 18 Feb 16 18:23 |
Decided to scallop (?) between the stringers to get uninterrupted lines. Gotta adjust that one. It's the only one I replaced after I broke it during the cowl shaping. Pictures really show stuff! |
| pfinn, Image # 35614 | 18 Feb 16 18:19 |
After a three week work blast (work work, Mars copter, full-size for JPL) completed the stringers and shaped the nose block (minus the intake ports, hollowing. and light glass). |
| Don C, Comment for image # 35526 | 06 Feb 16 09:42 |
| That really looks good. |
| poppy, Comment for image # 35526 | 06 Feb 16 03:11 |
| Beautiful "bones". Superb craftsmanship!! |
| pfinn, Image # 35526 | 05 Feb 16 22:22 |
Rayl inspired me! Pretty strange but effective motor mount. It achieved the correct right and down thrust. The offset geometry aligned the prop shaft dead center at the cowl (well, soon to be) exit for the spinner. |
| rayl, Comment for image # 35523 | 05 Feb 16 14:43 |
| Nice straight stringers. Grand bones.
|
| pfinn, Image # 35523 | 05 Feb 16 00:11 |
|
| pfinn, Image # 35522 | 05 Feb 16 00:08 |
Stringers on top and rear belly. Need to install servos, motor and push rods before closing up the rest of the stringers. |
| pfinn, Comment for image # 35519 | 04 Feb 16 23:49 |
| Thanks ;) |
| Skyediamonds1985, Comment for image # 35519 | 04 Feb 16 19:39 |
| I noticed pfinn even took the time to carefully bevel the ends of the diagonal fuselage bracing for a better fit, and still managed a very clean assembly. Excellent.!! |
| TJH, Comment for image # 35519 | 03 Feb 16 20:15 |
| I agree, super nice work! |
| Skyediamonds1985, Comment for image # 35519 | 03 Feb 16 18:22 |
| Very nice! Very clean. Excellent work. |
| pfinn, Image # 35519 | 03 Feb 16 00:16 |
|
| Build Thread, Page :
1 2 [ 3 ] 4 5 (95 posts, 20 posts per page, 5 pages in total)
|
[ < Prev ] [ Next > ] |
