| Build Thread, Page :
<< 5 6 7 8 9 10 11 12 13 14 15 (282 posts, 20 posts per page, 15 pages in total)
|
[ < Prev ] [ Next > ] |
| David Duckett, Image # 39647 | 04 Dec 17 18:43 |
THe engine is from the Guillows Corsair. |
| David Duckett, Comment for image # 39639 | 03 Dec 17 15:09 |
| Thank you very much! |
| Don C, Comment for image # 39639 | 03 Dec 17 11:10 |
| Starting to look more like a Duckett abode. I like it. |
| David Duckett, Image # 39641 | 02 Dec 17 19:07 |
|
| David Duckett, Image # 39639 | 02 Dec 17 19:04 |
Hung some paintings in the studio today. |
| David Duckett, Comment for image # 39635 | 01 Dec 17 16:31 |
| No. That is the same scheme as my Skyray so this one will be yellow. |
| heywooood, Comment for image # 39635 | 01 Dec 17 13:49 |
| that looks proper! Did I see you say this would be a Navy bird? Is that the red white and black trainer scheme? |
| David Duckett, Image # 39636 | 01 Dec 17 06:34 |
|
| David Duckett, Image # 39635 | 01 Dec 17 06:34 |
|
| David Duckett, Image # 39634 | 01 Dec 17 06:34 |
I'll sand it with 320 wet/dry sandpaper first and then apply another coat. |
| David Duckett, Image # 39633 | 01 Dec 17 06:32 |
I sprayed on one coat last night. This is a new product to me. It has a slight rough feel which is the filler part, I guess. |
| David Duckett, Comment for image # 39628 | 30 Nov 17 16:08 |
| At first he said "no aluminum" but when he saw what actually needed to be done he was ok with it. He was quite an interesting man. I asked if he also painted and he showed me a couple of photos of his work which is far more abstract than my stuff. He charged me $10 but when I wanted to put it on my card he said no because the shop would add a fee. Turns out he likes large canvases and I just happen to have a couple on hand. Deal! |
| rayl, Comment for image # 39628 | 30 Nov 17 15:54 |
| So.. What type of reaction did you get from the jewelry repairman when you took the cowling in? |
| Don C, Comment for image # 39629 | 30 Nov 17 10:40 |
| Looking good, DD. These really are/were sturdy kits for c/l flying. |
| David Duckett, Image # 39631 | 30 Nov 17 07:02 |
|
| David Duckett, Image # 39629 | 30 Nov 17 07:01 |
I have block sanded the aluminum cowling, a lot, and used Squadron White Putty to fill in the low areas. Later today I'll give it a shot of Rustoleum Filler and Primer. |
| David Duckett, Image # 39628 | 30 Nov 17 06:57 |
He also straightened the areas around the top and side intakes. |
| David Duckett, Image # 39627 | 30 Nov 17 06:56 |
I took it to a jewelry repair man who cut out the hole for the landing gear. |
| David Duckett, Comment for image # 39625 | 28 Nov 17 07:30 |
| It's designed for U-Control. There are several foamies available and I think they are fairly close in size. |
| BriandKilby, Comment for image # 39625 | 28 Nov 17 07:13 |
| is that a r/c kit dd?
|
| Build Thread, Page :
<< 5 6 7 8 9 10 11 12 13 14 15 (282 posts, 20 posts per page, 15 pages in total)
|
[ < Prev ] [ Next > ] |
