| Build Thread, Page :
<< 4 5 6 7 8 [ 9 ] 10 (189 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
| poppy, Comment for image # 21052 | 07 Feb 11 10:07 |
| Super!! |
| stvtptn, Comment for image # 20730 | 07 Feb 11 03:52 |
| really fine workmanship-excellent! |
| moostang51, Image # 21054 | 06 Feb 11 13:52 |
Brake flap. |
| moostang51, Image # 21053 | 06 Feb 11 13:51 |
Scaled from a 1/72 scale model. Templates make it go fast. |
| moostang51, Image # 21052 | 06 Feb 11 13:50 |
Next up, brake flaps. |
| David Duckett, Comment for image # 20824 | 29 Jan 11 06:36 |
| Of course. These look far better than the cast pieces. In fact, this entire build looks great and the attention to the detailing is superb. Adding the driveshaft is an inspired touch. |
| moostang51, Comment for image # 20824 | 28 Jan 11 17:13 |
| Thank you, David. Unfortunately due to my recessed gear bay mods, the cast resin pieces were too short. I tried to extend them with styrene tube and white putty, urggh.. but the line up for struts, just didn't look right. With your approval of course, I will offer the extra set of cast resin pieces you made for me to another builder of a Mossie or P-39. |
| David Duckett, Comment for image # 20824 | 28 Jan 11 16:43 |
| Lovely, lovely work. This is going to be stunning! |
| moostang51, Image # 20824 | 28 Jan 11 16:21 |
"Uni-pod" landing gear? |
| moostang51, Image # 20819 | 28 Jan 11 06:05 |
Front landing gear bay installed. |
| moostang51, Comment for image # 20788 | 27 Jan 11 04:02 |
| Thanks. Rivets are made with a push pin on the back side of .10 styrene using an aluminum ruler as a guide. Once painted and clear coated (future acrylic polish) a watery slush mix of umber, black and some dawn dish-washing detergent will be applied and then wiped off when dry for weathering. Chicken foot dials, knobs, and switches etc. will be touched up by color if necessary. |
| pfinn, Comment for image # 20788 | 26 Jan 11 21:06 |
| Nice detail. Rivets are cool. CA? |
| moostang51, Image # 20788 | 26 Jan 11 19:34 |
Almost ready for base paint. Will try to match a close "Bell" green. Will need it for wheel bays also. Where the hell is my color wheel? |
| frwyflyer, Comment for image # 20779 | 25 Jan 11 19:20 |
| The cockpit bling is looking very nice. The drive shaft is a very nice touch |
| moostang51, Image # 20780 | 25 Jan 11 18:45 |
Filled in recessed exhaust manifold, and front gear bay started. |
| moostang51, Image # 20779 | 25 Jan 11 18:41 |
Beginning cockpit bling. |
| John M Oshust, Comment for image # 20756 | 23 Jan 11 12:55 |
| Moos...join the eye club! My Doc says I have Cadillacs....maybe even Lincolns!!!!
|
| lukebozek1, Comment for image # 20756 | 23 Jan 11 12:13 |
| I can hear it now, "If you get any of that fingernail polish smelling stuff on that new oak table we will be shoppping for a new one today!" This is the voice of experience! So cold outside I moved indoors too. |
| moostang51, Image # 20756 | 23 Jan 11 11:37 |
Eyes need a little help. 2x magnifier allows better viewing of resin part cleanup. |
| moostang51, Image # 20755 | 23 Jan 11 11:33 |
Details starting. Modified exhaust and Front landing gear bay. Resin parts courtesy of DD. Thanks, David. |
| Build Thread, Page :
<< 4 5 6 7 8 [ 9 ] 10 (189 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
