| Build Thread, Page :
1 2 3 [ 4 ] 5 6 7 8 9 (160 posts, 20 posts per page, 9 pages in total)
|
[ < Prev ] [ Next > ] |
| Don C, Comment for image # 43185 | 14 May 21 10:42 |
| Sehr gut! |
| BriandKilby, Image # 43185 | 13 May 21 16:40 |
i have learn to translate german colors from building german planes. rlm 71 dunkelgrun or dark green. |
| BriandKilby, Image # 43184 | 13 May 21 16:37 |
|
| BriandKilby, Comment for image # 43168 | 03 May 21 08:14 |
| thanks ed, i'll try that. |
| edtherenderman, Comment for image # 43168 | 03 May 21 08:08 |
| I really had this problem on the Taube. I got to the point where I put waxed paper down on my building board and used t-pins to hold the very edges down. Dope one side,let it dry, flip it over, do the other side. I'm using eze dope at 1:2(1 dope : 2 water) and put lots of coats on. It came out pretty flat overall. |
| BriandKilby, Comment for image # 43168 | 03 May 21 07:31 |
| thanks don and bsadonkill. |
| bsadonkill, Comment for image # 43168 | 02 May 21 22:37 |
| A couple of drops of castor oil per ounce of nitrate dope and thinner will help. |
| BriandKilby, Comment for image # 43168 | 02 May 21 19:17 |
| :) |
| Don C, Comment for image # 43168 | 02 May 21 13:22 |
| Yes it does. I'm waiting to see if any one does have an answer. I just try not to get it too wet.
|
| BriandKilby, Comment for image # 43168 | 02 May 21 10:05 |
| maybe you guys can help me? sometimes when i dope thin balsa areas like the elevator it tends to warp it. is there a way to avoid this? thanks, brian. |
| BriandKilby, Image # 43168 | 01 May 21 15:50 |
light blue underside. |
| BriandKilby, Comment for image # 43033 | 29 Apr 21 09:41 |
| thanks ed and luke. |
| lukebozek1, Comment for image # 43033 | 29 Apr 21 07:53 |
| Brian this looks great. I see you applied tissue to the fuselage in sections and it's near perfect. I will try this on the one I am working right now. |
| edbecky, Comment for image # 43033 | 28 Apr 21 16:56 |
| Nice tight covering.
|
| BriandKilby, Comment for image # 43033 | 28 Apr 21 16:01 |
| was warm enough to dope the butcher bird, start camouflage next. |
| bsadonkill, Comment for image # 43033 | 28 Feb 21 22:28 |
| Nice neat job cutting slots in the spinner. |
| BriandKilby, Comment for image # 43033 | 28 Feb 21 13:59 |
| thanks don! i just build it up with a balsa rear section canopy, as the plans show, looks sort of like a balsa roll cage. |
| Don C, Comment for image # 43033 | 28 Feb 21 13:45 |
| Looks good. What did you come up with for the back of the canopy?
|
| BriandKilby, Image # 43033 | 28 Feb 21 11:30 |
working on props! |
| BriandKilby, Image # 43032 | 28 Feb 21 11:29 |
|
| Build Thread, Page :
1 2 3 [ 4 ] 5 6 7 8 9 (160 posts, 20 posts per page, 9 pages in total)
|
[ < Prev ] [ Next > ] |
