| Build Thread, Page :
1 2 3 [ 4 ] 5 6 7 8 9 10 (193 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
| John M Oshust, Image # 11102 | 04 Mar 09 18:45 |
I cannot mark the upper air foil until I complete the ailerons. |
| John M Oshust, Image # 11101 | 04 Mar 09 18:43 |
Mass specs, Otto's signature logo, and an iron cross.....today was graphics and decal day. |
| John M Oshust, Image # 11100 | 04 Mar 09 18:41 |
Port side, please note the small Pfalz logo on the rudder. |
| JohnG., Comment for image # 11094 | 04 Mar 09 12:20 |
| SNAZZ...ZEE!!!! |
| John M Oshust, Image # 11094 | 04 Mar 09 11:43 |
I am glad that this part of the paint is over. |
| John M Oshust, Image # 11087 | 03 Mar 09 19:44 |
Otto fired up the engine for a test run. The number 11 hole was misfiring. Magneto problem. THe problem has been corrected. |
| John M Oshust, Comment for image # 11086 | 03 Mar 09 19:40 |
| Otto fired up the engine for a test. The number 11 holes was misfiring. A magneto problem. The problem has been corrected. |
| John M Oshust, Image # 11085 | 03 Mar 09 19:10 |
I installed the MGs and Otto sighted them in. Port gun kept jamming. Problem with the ammunition. |
| John M Oshust, Image # 11084 | 03 Mar 09 19:09 |
Started planning the garphics. |
| John M Oshust, Image # 11083 | 03 Mar 09 19:07 |
I painted some color on the feathers. |
| John M Oshust, Image # 11082 | 03 Mar 09 19:05 |
The eveil cat "Misty" stalks the Pfalz. If he touches this plane, he is history! |
| John M Oshust, Image # 11081 | 03 Mar 09 19:03 |
I did not get to the middle wing fillets today.....did not need the stress! |
| John M Oshust, Image # 11073 | 02 Mar 09 17:36 |
I played with the new saw and made this from scrap. Useful while painting but necessary to sight in the machine guns. |
| John M Oshust, Image # 11072 | 02 Mar 09 17:34 |
Shaped and filled...the evil fillet is no more. |
| John M Oshust, Image # 11071 | 02 Mar 09 17:33 |
After a coat of paint. |
| John M Oshust, Image # 11070 | 02 Mar 09 17:32 |
Fillet mignon. |
| John M Oshust, Comment for image # 11069 | 02 Mar 09 17:29 |
| Two small fillets are still required for the middle wing....tomorrow! |
| John M Oshust, Image # 11069 | 02 Mar 09 17:28 |
|
| John M Oshust, Comment for image # 11057 | 01 Mar 09 20:24 |
| Moos,it was a Mother Seton HS here near Cranford. The saw and compressor were the only tools there. Might have to give the airbrush a go the next time around. |
| moostang51, Comment for image # 11057 | 01 Mar 09 16:47 |
| Sweet. Compressor with regulator, dremel table saw....Was the show at the convention Center in Raritan? |
| Build Thread, Page :
1 2 3 [ 4 ] 5 6 7 8 9 10 (193 posts, 20 posts per page, 10 pages in total)
|
[ < Prev ] [ Next > ] |
