Build Thread, Page :
1 2 [ 3 ] 4 5 6 7 8 9 10 11 (200 posts, 20 posts per page, 11 pages in total)
|
[ < Prev ] [ Next > ] |
Creosotewind, Comment for image # 10149 | 10 Dec 08 13:34 |
Lens stopped down to f8. Looks like a nighttime shot. |
Creosotewind, Image # 10149 | 10 Dec 08 13:33 |
Shot in the middle of the day with a flash. |
Creosotewind, Image # 10148 | 10 Dec 08 13:32 |
|
Creosotewind, Image # 10147 | 10 Dec 08 13:32 |
|
Creosotewind, Image # 10146 | 10 Dec 08 13:31 |
|
Creosotewind, Image # 10145 | 10 Dec 08 13:30 |
Starting a walk around. |
Creosotewind, Image # 10144 | 10 Dec 08 13:30 |
I like this photo. |
Creosotewind, Image # 10143 | 10 Dec 08 13:29 |
|
Creosotewind, Image # 10142 | 10 Dec 08 13:28 |
I probably won't be building for a while, but I wanted to post a few final shots of the Cub. |
Creosotewind, Comment for image # 10054 | 01 Dec 08 09:08 |
I put it off until the last, since I haven't carved anything except a turkey for the last 35 years or so. Three pieces of 1/16" basswood. I am surprised it turned out so well. I still need to finish the prop hub, varnish the prop and add the brass edging. But very nearly done. Oh yeah, the black tubes on the landing gear are soda straws covered in masking tape, painted black. These were canvas or leather covers that protected the springs for the l.g. |
Creosotewind, Comment for image # 10050 | 01 Dec 08 09:01 |
The brakes are hard to see, but made from snap connectors, like those used to snap canvas flaps together. They were soldered to a washer and brass tube, and then cut down with a Dremel, removing about half the snap so it looks like a brake (or at least sorta looks like a brake). Wheels are glued in place. |
Creosotewind, Comment for image # 10049 | 01 Dec 08 08:58 |
The one on the left is the original, and the one on the right shows the cover. The aluminum is just shaped over the wheel, and slowly cut so it wraps under the original wheel. It is not glued, just pressed in place. Once there, the aluminum is lightly scuffed with sandpaper to better accept paint. |
Creosotewind, Image # 10054 | 01 Dec 08 08:56 |
Still need to finish the prop. But man, what fun it was to carve. |
Creosotewind, Image # 10053 | 01 Dec 08 08:55 |
Another cockpit shot. The Cub is showing its fangs. |
Creosotewind, Image # 10052 | 01 Dec 08 08:54 |
Bazookas in place. Nut attachments are resin, from a Verlinden detail set. |
Creosotewind, Image # 10051 | 01 Dec 08 08:53 |
Tailwheel and control wires in place. Gotta build that Skyray soon. |
Creosotewind, Image # 10050 | 01 Dec 08 08:52 |
Wheels in place, along with my attempt at brake drums. |
Creosotewind, Image # 10049 | 01 Dec 08 08:51 |
Wheel covers made from aluminum sheet. |
Creosotewind, Image # 10048 | 01 Dec 08 08:50 |
The bazookas, painted and mounted to their platforms |
poppy, Comment for image # 9816 | 14 Nov 08 10:02 |
JFB! |
Build Thread, Page :
1 2 [ 3 ] 4 5 6 7 8 9 10 11 (200 posts, 20 posts per page, 11 pages in total)
|
[ < Prev ] [ Next > ] |